m^
。red]Error Code 149。 System error code 149 means \substitute a drive for which a directory on the drive is the target of a previous substitute.\This error code may also display as \。red]Error Code 150。 System error code 150 means \specified in your CONFIG.SYS file or tracing is disallowed.\as \
。red]Error Code 151。 System error code 151 means \events for DosMuxSemWait is not correct.\
!p
m&o
V4m
B*X)U8z
&rH.[
O
}#f2LH/] I5u
来自。#000000]hanfei_5759。的总结：
[url=http://bbs.simwe.com/viewthread.php?tid=857889]http://bbs.simwe.com/viewthread.php?tid=857889[/url]
yywj2000 发表于 2009-3-13 15:06 WARING
THE SLAVE SURFACES ASSEMBLY_CP-4-DAZHOUHOU-1 AND
ASSEMBLY_CP-5-DAZHOUHOU-1 INTERSECT EACH OTHER. THEY ARE PAIRED WITH MASTER SURFACES ASSEMBLY_CP-4-LIANGANHOU-1 AND
ASSEMBLY_CP-5-LIANGANHOU-1 THAT ALSO INTERSECT EACH OTHER. IF BOTH PAIRS ARE *CONTACT PAIRs, THESE TWO PAIRS SHOULD NOT BE SIMULTANEOUSLY PRESENT IN A STEP BECAUSE OF POSSIBLE CONVERGENCE PROBLEMS; USE *MODEL
CHANGE,TYPE=CONTACT PAIR TO REMOVE ONE OF THEM. IF BOTH ARE *TIE PAIRS, THE REDUNDANT TIES WILL BE REMOVED AUTOMATICALLY. IF ONE PAIR IS *TIE AND ANOTHER IS *CONTACT PAIR, REMOVE ONE OF THEM. 不知道怎么解决
jzc1983 发表于 2009-3-13 19:46 8 nodes may have incorrect normal definitions. The nodes have been identified in node set WarnNodeIncorrectNormal. 节点有错误的法线定义？
jzc1983 发表于 2009-3-14 11:17 [i=s] 本帖最后由 jzc1983 于 2009-3-14 11:20 编辑 [/i]
\
THE SLAVE SURFACE ASSEMBLY_TANHUANG IS PAIRED WITH MASTER SURFACES ASSEMBLY_TONGBI AND ASSEMBLY_TONGDI THAT INTERSECT EACH OTHER. IF BOTH
PAIRS ARE *CONTACT PAIRs, THESE TWO PAIRS SHOULD NOT BE SIMULTANEOUSLY PRESENT IN A STEP BECAUSE OF POSSIBLE CONVERGENCE PROBLEMS; USE *MODEL CHANGE,TYPE=CONTACT PAIR TO REMOVE ONE OF THEM. IF BOTH ARE *TIE PAIRS, THE REDUNDANT TIES WILL BE REMOVED AUTOMATICALLY. IF ONE PAIR IS *TIE AND ANOTHER IS *CONTACT PAIR, REMOVE ONE OF THEM.
l+V
U
\\4x
我这个警告和6楼是一样的，就是零件1的侧面和零件2的侧面接触，零件1的地面和零件2的地面接触，警告说不能同时在一个step里面设顶，我都是在initial step里面设的
xiaofeng02320 发表于 2009-3-16 12:34 下了，谢谢
sillyoranger 发表于 2009-3-30 16:01 在做岩土工程方面的 也出现一个问题
n0x? X _5Bc/F
在第一步 GEOSTATIC分析步施加重力和房屋载荷 加上边界条件 边界条件是5个面简支约束 自由面上表面(施加房屋载荷的那个面 大变形off 为什么会出现 ERROR:Fixed time is too large.
i-l.s
-C*uv2M
>???????
zsq-w 发表于 2009-3-30 16:41 [i=s] 本帖最后由 zsq-w 于 2009-4-14 18:42 编辑 [/i]
.V
\\$r j:t{$Y3q!OV:Y
[b]1 [/b]上文已经说过，类似于
----------------------------------------------------------------------------------------------------------
。。 ERROR:Too many attamps have been made。
m$u+?
A'x9u.Z
。。 Too many attamps have been made....。
%u b0O-p1i4Eq
。。 THE SOLUTION APPEARS TO BE DIVERGING. CONVERGENCE ISJUDGED UNLIKELY. 。
。。 TIME INCREMENT REQUIRED IS LESS THAN THE MINIMUM SPECIFIED Analysis Input File Processor exited with an error.。
&M4@ x'R
d1k
G0m
@:U
。purple]。
#000000]-----------------------------------------------------------------------------------------------------------。
k e9p
F)f
