ASM Assembly Automation Ltd.
AD809-06 操作手册
附录
模式 操作表# 項目 2 Ejector Up Level 說明 This level will totally free up the die from the mylar tape adhesion. The height of the ejector pin should be about one die thick at this level. ColletDieEjector UpLevelEjector PinEjector Cap Surface 7 8 9 Ejector Valve Collet Vacuum Epoxy Drum Sole To Enable or Disable the ejector cap vacuum To Enable or Disable the collet vacuum Not capable for standard AD809-06 machine 40
ASM Assembly Automation Ltd.
AD809-06 操作手册
附录
4.3 BOND Parameter (焊接參數)
0 1 2 3 4 5 6 7 8 9 BOND PARAMETERSDelaysMotor SpeedsWalking Path Size0Wafer EdgeSrch Num4Units To Bond (x1K)0Missing Die DetectEnableCurr Die Repick Count5Contact PickDisableContact BondDisableBond Inked DieDisable00 1 2 3 4 5 6 7 8 9 SET DELAYSArm Pick DelayHead Pick DelayEjector Up DelayPick DelayArm Bond DelayHead Bond DelayBond DelayPR DelayIndex WH DelayWeak Blow Delays20702050206050702000 1 2 3 4 5 6 1SET MOTOR SPEEDSBond ArmSlowBond Head UpFastBond Head DownNormalEjectorSlowTable XNormalTable YNormalPasswordDisable
Mode Menu # Title Para-0 Delay Menu meter 0 Arm Pick Delay 1 2 3 4 5 6 7 Description 用於執行延遲參數數據輸入功能。 To specify the time delay just after the bonding process has been completed and before the bond arm starts to rotate to pre-pick position. The default value is 20. Head Pick Delay To specify the time delay just after the bond arm reaches the pick position and before it will reach the pick level. The default value is 70. Eject Up Delay To specify the time delay just when the bond head stops descending and before the ejector start rising up. The default value is 20. Pick Delay To specify the time for the bond arm to remain at pick up level after the ejector up and return to its home position. The default value is 50. Arm Bond To specify the time delay just after the picking process Delay has been completed and before the bond arm starts to rotate to pre-bond position. The default value is 20. Head Bond To specify the time delay just after the bond head Delay reaches its bond position and before it goes down to reach the bond level. The default value is 60. Bond Delay To specify the time delay for the bond arm to remain at the bond level before going up. The default value is 50. PR Delay To specify the time delay when the X-Y Table stop and before PR system starts to recognize a pattern. The default is 70. 41
ASM Assembly Automation Ltd.
AD809-06 操作手册
附录
Mode Menu # Title 8 Index WH Delay 9 Wblow On Delay Description Delay after die bonded on the substrates and the w/h table starts to index. The duration for weak airflow blow from the collet before the bondhead rises from bond level to home level. bondheadz-levelbond levelvalve openpressurizedair valvevalve closewblow bond delayvalve close 1 Set Motor Speeds Bond Arm 0 1 Bond head Up 2 3 4 5 6 Bond head Down Ejector Table –X Table –Y Password This is to perform the profile parameters of the respective motors. Optionally, a password is required to access this information. 焊臂馬達驅動?運動 The bond arm motor drives the theta motion of the bondarm itself. 焊頭可作兩種運動, 上升及下降。The bond head is divided into two motions, up and down. Separate profiles are available to each motion. The down profile may be slower than up motion to prevent excessive vibration when collet is in contact with the die. For sensitive die, slow speed for ejector may avoid die from cracking or breaking. X軸馬達的速度。 Y軸馬達的速度。 用於封鎖控制器參數及馬達速度狀態。 42
ASM Assembly Automation Ltd.
AD809-06 操作手册
附录
4.4 SERVICE Mode (輔助模式)
0 1 2 3 4 5 6 7 8 9 SERVICE MODEFormat New DiskSave Controller ParamRestore Controller ParamSave WH ParamRestore WH ParamPrint Controller ParamPrint StatisticsShow StatisticsClear StatisticsSet Date and Time7BOND STATISTICSSince Day-Month-YearTimeTotal Up Time= 0.00:00Total Idle Time= 0.00:00Ave. Cycle Time= 0 msTotal Units= 0Inked Die Count= 0Chip Die Count= 0Unsuccessful Pick= 0Collet Jam Count= 0
Mode Menu # Title Service 0 Format New Disk 1 Save Controller Param 2 Restore Controller Param 3 Save WH Param 4 Restore WH Param 5 Print Controller Param 6 Print Statistics 7 Show Statistics Description 將新磁碟格式化。 儲存控制器參數到已格式化的磁碟。 開啟在磁碟內的控制器參數。 儲存工作夾具參數到磁碟。 開啟在磁碟內的工作夾具參數。 列印參數表到配有RS-232介面的印表機。 8 9 列印焊接統計表到印表機。 顯示由某個指定時間至最後焊接單元的總工作時間、總停機時間、平均週期時間、總產量、印墨管芯計數、裂片管芯計數、不能成功拾取和吸咀阻塞計數的統計結果。 Clear Statistics 用於清除統計記錄。 Set Date and Time 按[ADV]或[RTD]鍵設定日期及時間, 然後按[ENTER]。 43
