嵌入式实习报告

主程序模板

// File Name : 2410test.c

// Function : S3C2410 Test Main Menu // Program : Shin, On Pil (SOP) // Date : June 13, 2003 // Version : 0.0 // History

//====================================================================

#include #include

#include \#include \#include \#include \#include \

#include \#include \

void Isr_Init(void); void HaltUndef(void); void HaltSwi(void);

20

void HaltPabort(void); void HaltDabort(void);

extern void __rt_lib_init( void ) ;

void Temp_Function( void ) { ; }

//=================================================================== void Main(void) {

int i=0;

// Led_Display(15);

MMU_Init(); //初始化MMU单元

#if ADS10

__rt_lib_init(); //for ADS 1.0 #endif

// ChangeClockDivider(0,0); // 1:1:1 // ChangeClockDivider(0,1); // 1:1:2 // rCLKDIVN |= (1<<2); // 1:4:4

21

// ChangeClockDivider(1,0); // 1:2:2 ChangeClockDivider(1,1); // 1:2:4

// ChangeMPllValue(0xa1,0x3,0x3); // FCLK=50.7MHz // //

ChangeMPllValue(0x7f,0x2,0x2); ChangeMPllValue(0x96,0x5,0x1);

// //

FCLK=101.25MHz FCLK=135428571Hz

// ChangeMPllValue(0x2a,0x1,0x0); // FCLK=200MHz // ChangeMPllValue(0x5c,0x1,0x1); // FCLK=200MHz // ChangeMPllValue(0x5c,0x4,0x0); // FCLK=200MHz

// ChangeMPllValue(0x8e,0x7,0x0); // FCLK=200MHz ChangeMPllValue(0xa1,0x3,0x1); // FCLK=202.8MHz // ChangeMPllValue(0x66,0x1,0x1); // FCLK=220MHz // ChangeMPllValue(0x69,0x1,0x1); // FCLK=226MHz // ChangeMPllValue(0x96,0x2,0x1); // FCLK=237MHz // ChangeMPllValue(0x7d,0x4,0x0); // FCLK=266MHz

Port_Init();

//Save the wasted power consumption on GPIO. rIISPSR=(2<<5)|(2<<0); @384fs,PCLK=50Mhz.

22

//IO端口初始化 //设中断

Isr_Init();

Uart_Init(0,115200);//COM口初始化

//IIS_LRCK=44.1Khz

rGPHCON = rGPHCON & ~(0xf<<18)|(0x5<<18); //CLKOUT 0,1=OUTPUT to reduce the power consumption.

Uart_Printf(\ }

//=================================================================== void Isr_Init(void) {

pISR_UNDEF = (unsigned)HaltUndef; pISR_SWI = (unsigned)HaltSwi; pISR_PABORT = (unsigned)HaltPabort; pISR_DABORT = (unsigned)HaltDabort;

23

while( 1 ) { }

Delay(2000);//延时 i++; if (i>15) i=0;

Led_Display(i);//控制四个LED显示

Uart_Printf(\串口返回调试信息