46.
A05G
AMG
(Refer to General figure 20.) Troubleshooting an open circuit with a voltmeter as shown in this circuit will
A) permit current to flow and illuminate the lamp.
B) create a low resistance path and the current flow will be greater than normal.C) permit the battery voltage to appear on the voltmeter.
47.
A05G
AMG
(Refer to General figure 16.) What will be the effect if the PCO relay fails to operate when the left hand tank is selected?
A) The fuel pressure crossfeed valve will not open.B) The fuel tank crossfeed valve open light will illuminate.C) The fuel pressure crossfeed valve open light will not illuminate.
48.
A05G
AMG
(Refer to General figure 23.) If an open occurs at R1, the lightA) cannot be turned on.B) will not be affected.C) cannot be turned off.
49.
B02G
AMG
For sketching purposes, almost all objects are composed of one or some combination of six basic shapes; these include the
A) angle, arc, line, plane, square, and circle.B) triangle, circle, cube, cylinder, cone, and sphere.C) triangle, plane, circle, line, square, and sphere.
50.
B02G
AMG
(1) According to 14 CFR Part 91, repairs to an aircraft skin should have a detailed dimensional sketch included in the permanent records.
(2) On occasion, a mechanic may need to make a simple sketch of a proposed repair to an aircraft, a new design, or a modification.Regarding the above statements,A) only No. 1 is true.B) only No. 2 is true.
C) both No. 1 and No. 2 are true.
51.
B02G
AMG
(Refer to General figure 31.) What are the proper procedural steps for sketching repairs and alterations?A) 3, 1, 4, 2.B) 4, 2, 3, 1.C) 1, 3, 4, 2.
52.
B02G
AMG
What should be the first step of the procedure in sketching an aircraft wing skin repair?A) Draw heavy guidelines.B) Lay out the repair.C) Block in the views.
53.
B02G
AMG
What is the class of working drawing that is the description/depiction of a single part?A) Installation drawing.B) Assembly drawingC) Detail drawing.
54.
B03G
AMG
(Refer to General figure 34.) What would be the minimum diameter of 4130 round stock required for the construction of the clevis that would produce a machined surface?A) 55/64 inch.B) 1 inch.C) 7/8 inch.
55.
B03G
AMG
In the reading of aircraft blueprints, the term 'tolerance', used in association with aircraft parts or components,
A) is the tightest permissible fit for proper construction and operation of mating parts.
B) is the difference between extreme permissible dimensions that a part may have and still be acceptable.
C) represents the limit of galvanic compatibility between different adjoining material types in aircraft parts.
56.
B03G
AMG
(1) A measurement should not be scaled from an aircraft print because the paper shrinks or stretches when the print is made.
(2) When a detail drawing is made, it is carefully and accurately drawn to scale, and is dimensioned.Regarding the above statements,
A) only No. 2 is true.
B) both No. 1 and No. 2 are true.C) neither No. 1 nor No. 2 is true.
57.
B03G
AMG
A drawing in which the subassemblies or parts are shown as brought together on the aircraft is called
A) an assembly drawing.B) an installation drawing.C) a detail drawing.
58.
B03G
AMG
In what type of electrical diagram are images of components used instead of conventional electrical symbols?
A) A pictorial diagram.B) A schematic diagram.C) A block diagram.
59.
B01G
AMG
(Refer to General figure 27.) In the isometric view of a typical aileron balance weight, identify the view indicated by the arrow.A) 1.B) 3.C) 2.
60.
B01G
AMG
Which statement is true regarding an orthographic projection?A) There are always at least two views.B) It could have as many as eight views.
C) One view, two view, and three view drawings are the most common.
61.
B01G
AMG
Which of the following terms is/are used to indicate specific measured distances from the datum and/or other points identified by the manufacturer, to points in or on the aircraft?1. Zone numbers.2. Reference numbers.3. Station numbers.A) 1 and 3.B) 3.
C) 2
62.
B01G
AMG
(1) Schematic diagrams indicate the location of individual components in the aircraft.
(2) Schematic diagrams indicate the location of components with respect to each other within the system.
Regarding the above statements,A) only No. 1 is true.
B) both No. 1 and No. 2 are true.C) only No. 2 is true.
63.
B04G
AMG
(Refer to General figure 40.) Determine the proper tension for a 3/16-inch cable (7 x 19 extra flex) if the temperature is 87 °F.A) 135 pounds.B) 125 pounds.C) 140 pounds.
64.
B04G
AMG
(Refer to General figure 39.) Determine the minimum wire size of a single cable in a bundle carrying a continuous current of 20 amperes 10 feet from the bus to the equipment in a 28-volt system with an allowable 1-volt drop.A) No. 12.B) No. 14.C) No. 16.
65.
C02G
AMG
When computing the maximum forward loaded CG of an aircraft, minimum weights, arms, and moments should be used for items of useful load that are located aft of theA) rearward CG limit.B) forward CG limit.C) datum.
66.
C02G
AMG
An aircraft as loaded weighs 4,954 pounds at a CG of +30.5 inches. The CG range is +32.0 inches to +42.1 inches. Find the minimum weight of the ballast necessary to bring the CG within the CG range. The ballast arm is +162 inches.A) 61.98 pounds.B) 30.58 pounds.
